Search Frequent Questions

Filter By:

Active filters:

Remove all filters

Displaying 1 - 15 of 50 results

  • How do I Create Scripts to run MOVES3 from the Command Line?

    See More Frequent Questions about MOVES and Related Models . While the easiest way to interact with MOVES3 is via its graphical user interface (GUI), it is sometimes useful to process MOVES RunSpecs in batches via the Windows command line. To this end, MOVES3 has a set of commands that…

    • Last published:

  • Obtaining an RMP ID Number

    How can a facility subject to the Risk Management Plan (RMP) requirements obtain its RMP ID number? The owner or operator of a regulated RMP facility that has already submitted an RMP, may obtain the facility's identification number (RMP ID Number) by contacting the RMP Reporting Center (703-227-7650). An RMP-covered…

    • Last published:

  • Does EPA have enforcement authority for the risk management program regulations?

    Yes. Under §113 of the CAA, the Agency has the authority to bring administrative and judicial actions against violators. Judicial actions can be civil and criminal in nature. Section 113(a)(3) authorizes the Agency to order violators to comply with the risk management program regulations. Under section 113(b), the Agency may…

    • Last published:

  • Criteria for selecting stationary sources to audit

    What criteria will be used to select stationary sources for periodic compliance audits of risk management plans (RMPs) submitted under 40 CFR Part 68, Subpart G? The implementing agency will, according to the regulations at 40 CFR §68.220(b), select stationary sources for audits based on any of the following criteria…

    • Last published:

  • Is there a citizen suit provision applicable to RMP?

    Is there a citizen suit provision applicable to CAA §112 and the risk management program rule? Yes, section 304 of the CAA includes a citizen suit provision for violations of emission standards or limitations promulgated under the Act.

    • Last published:

  • Accessing RMP Data

    Is Risk Management Plan (RMP) data available to the public and, if so, where can it be found? Risk Management Plans (RMPs) prepared and submitted pursuant to CAA section 112(r) are, by statute, available to the public. Members of the general public may obtain RMP data by visiting a designated…

    • Last published:

  • How may state and local rules be more stringent?

    In what ways may state and local rules be more stringent? Does this document ( General Risk Management Program Guidance ) provide guidance on state and local differences? States and localities may impose more detailed requirements, such as requiring more documentation or more frequent reporting, specifying hours of training or…

    • Last published:

  • Is There Any Documentation Available for Installing MOVES on Linux?

    See More Frequent Questions about MOVES and Related Models . MOVES is designed for the Windows operating system and the EPA MOVES Team only tests and supports MOVES in Windows environments. However, users have reported successfully installing and running MOVES in Linux. The instructions for Running MOVES from the Windows…

    • Last published:

  • Can I Install MOVES on a Server so More than One User Can Access It?

    See More Frequent Questions about MOVES and Related Models . No, MOVES is not a multi-user product. MOVES is primarily intended for use on a Windows10 64-bit personal computer. In addition, we have run MOVES2014a, MOVES2014b and MOVES3 on Windows Server 2012 R2 very successfully for years as a single…

    • Last published:

  • Statutory authority and regulatory source for the risk management program

    What is the statutory authority and the regulatory source for the risk management program regulations that are codified in 40 CFR Part 68? The risk management program regulations were promulgated pursuant to the §112(r) accidental release prevention provisions of the Clean Air Act, as amended in 1990. The regulatory sources…

    • Last published:

  • RMP Information Center

    If I have additional questions regarding the RMP regulations, who can I contact via telephone for further assistance? You may contact the EPCRA, RMP & Oil Information Center, a publicly accessible service that provides up-to-date information on the regulatory requirements of the RMP program, including the applicability, program levels, off-site…

    • Last published:

  • How do I automate MOVES installation (for example, with Microsoft Endpoint Manager)?

    The MOVES installer typically requires user interaction to make various selections. However, if the default installation options are acceptable for your needs, the installer can be run without user interaction on the command line using the /VERYSILENT flag. If this is a first time installation you will need to create…

    • Last published:

  • What are the Computer Hardware and Software Requirements for Installing and Running MOVES?

    See More Frequent Questions about MOVES and Related Models . MOVES is designed to run on a single personal computer with a Windows 10 or 11 operating system. The recommended minimum hardware for a desktop or laptop computer running MOVES are: 64-bit CPU with 4 or more cores: Intel i7…

    • Last published:

  • Vulnerable Zone Determination

    Vulnerable zones are areas that could be affected by a release from a chemical accident at a facility subject to the risk management program requirements in 40 CFR Part 68. How can one determine if they live or work within a vulnerable zone? The Vulnerable Zone Indicator System (VZIS) allows…

    • Last published:

  • Does MOVES work with the Apple Macintosh operating system (iOS)?

    See More Frequent Questions about MOVES and Related Models . MOVES is designed for the Windows operating system and EPA tests it only on Windows. We do not have the capability to adapt MOVES for iOS or test its use in an Apple environment. We expect MOVES can be used…

    • Last published: