Search Frequent Questions

Filter By:

Active filters:

Remove all filters

Displaying 1 - 15 of 60 results

  • Obtaining an RMP ID Number

    How can a facility subject to the Risk Management Plan (RMP) requirements obtain its RMP ID number? The owner or operator of a regulated RMP facility that has already submitted an RMP, may obtain the facility's identification number (RMP ID Number) by contacting the RMP Reporting Center (703-227-7650). An RMP-covered…

    • Last published:

  • Does EPA have enforcement authority for the risk management program regulations?

    Yes. Under §113 of the CAA, the Agency has the authority to bring administrative and judicial actions against violators. Judicial actions can be civil and criminal in nature. Section 113(a)(3) authorizes the Agency to order violators to comply with the risk management program regulations. Under section 113(b), the Agency may…

    • Last published:

  • Criteria for selecting stationary sources to audit

    What criteria will be used to select stationary sources for periodic compliance audits of risk management plans (RMPs) submitted under 40 CFR Part 68, Subpart G? The implementing agency will, according to the regulations at 40 CFR §68.220(b), select stationary sources for audits based on any of the following criteria…

    • Last published:

  • Is there a citizen suit provision applicable to RMP?

    Is there a citizen suit provision applicable to CAA §112 and the risk management program rule? Yes, section 304 of the CAA includes a citizen suit provision for violations of emission standards or limitations promulgated under the Act.

    • Last published:

  • Accessing RMP Data

    Is Risk Management Plan (RMP) data available to the public and, if so, where can it be found? Risk Management Plans (RMPs) prepared and submitted pursuant to CAA section 112(r) are, by statute, available to the public. Members of the general public may obtain RMP data by visiting a designated…

    • Last published:

  • How may state and local rules be more stringent?

    In what ways may state and local rules be more stringent? Does this document ( General Risk Management Program Guidance ) provide guidance on state and local differences? States and localities may impose more detailed requirements, such as requiring more documentation or more frequent reporting, specifying hours of training or…

    • Last published:

  • How does the Safe Drinking Water Act limit lead in pipes, plumbing fittings, fixtures, faucets, solder and flux?

    Answer: Section 1417 of the Safe Drinking Water Act (SDWA) establishes the definition for “lead free” as a weighted average of 0.25% lead calculated across the wetted surfaces of a pipe, pipe fitting, plumbing fitting, and fixture and 0.2% lead for solder and flux. The Act also provides a methodology…

    • Last published:

  • Is exposure to lead contaminated drinking water from absorption through skin a health threat?

    Answer: Human skin does not absorb lead in water. For more information visit our website: https://www.epa.gov/ground-water-and-drinking-water/basic-information-about-lead-drinking-water . Question (23002-32377) Find a printable PDF copy of all frequent questions pertaining to lead .

    • Last published:

  • Are non-transient, non-community water systems (NTNCWSs) required to monitor for lead and copper?

    Answer: All community water systems (CWSs) and NTNCWSs must collect lead and copper tap samples. The frequency of the monitoring and number of samples to be collected and analyzed is based primarily on the number of people served and tap water monitoring results. For an outline of monitoring requirements (e.g…

    • Last published:

  • Is there anything else I can do beyond flushing my tap or buying bottled water?

    Answer: Yes, find “Important Steps You Can Take to Reduce Lead in Drinking Water” if you are concerned about lead in their drinking water. The list is not intended to be exhaustive or to imply that all actions equally reduce lead from drinking water. EPA recommends you also contact your…

    • Last published:

  • My neighbors got their water tested and found lead. Is my water safe?

    Answer: Lead usually gets into drinking water through contact with plumbing materials such as lead pipes or lead solder, or faucets, valves, and fixtures made of brass (brass contains some lead). Since each home has different plumbing pipes and materials, test results are likely to be different for each home…

    • Last published:

  • Can one still sell lead solder under the Lead Ban?

    Answer: Section 1417(a)(3) of the Safe Drinking Water Act (SDWA) prohibits the sale of solder and flux that is not lead-free unless the solder or flux bears a prominent label stating that it is illegal to use the solder or flux in the installation or repair of any plumbing providing…

    • Last published:

  • Why do water systems add phosphate to drinking water? What are the health effects of drinking water containing phosphates? 

    Answer: Public water systems (PWSs) commonly add phosphates to drinking water to prevent the release of metals in drinking water. Orthophosphate is most commonly used for lead and copper control. Polyphosphates sequester iron and manganese to prevent discolored water but are not effective to control lead and copper. Blended phosphates…

    • Last published:

  • Statutory authority and regulatory source for the risk management program

    What is the statutory authority and the regulatory source for the risk management program regulations that are codified in 40 CFR Part 68? The risk management program regulations were promulgated pursuant to the §112(r) accidental release prevention provisions of the Clean Air Act, as amended in 1990. The regulatory sources…

    • Last published:

  • RMP Information Center

    If I have additional questions regarding the RMP regulations, who can I contact via telephone for further assistance? You may contact the EPCRA, RMP & Oil Information Center, a publicly accessible service that provides up-to-date information on the regulatory requirements of the RMP program, including the applicability, program levels, off-site…

    • Last published: