Search Frequent Questions

Filter By:

Active filters:

Remove all filters

Displaying 1 - 15 of 35 results

  • How do I Obtain the Populations for Each of the MOVES Source Types?

    See More Frequent Questions about MOVES and Related Models . To output vehicle populations, when setting up your RunSpec select the "Inventory" calculation type from the Scale panel and the "Population" activity option from the General Output panel of the MOVES GUI. The movesactivityoutput table in your MOVES output database…

    • Last published:

  • How are Counties Mapped to Fuel Regions in MOVES? How Can I Substitute Alternate Fuel Formulations?

    See More Frequent Questions about MOVES and Related Models . The RegionCounty table in the MOVES default database maps each county to a MOVES fuel region (defined by regionCodeID). If you are conducting a County or Project Scale Run, you do not need to modify this table to use alternate…

    • Last published:

  • When testing a work area, does one lead test kit or paint chip sample suffice for any single component?

    The certified renovator is only required to use one lead test kit or paint chip sample for each component, even if the surface of the component is extensive (e.g., a large wall). Question Number: 23002-23865 Find a printable PDF copy of all frequent questions pertaining to lead .

    • Last published:

  • Can a homeowner use an EPA-recognized lead test kit to check for lead-based paint?

    Answer: A number of lead test kits are available for consumer purchase in most retail hardware stores; however, the Consumer Product Safety Commission (CPSC) states that consumers should exercise caution when using these lead test kits to evaluate consumer products for potential lead exposures. Find more information online . To…

    • Last published:

  • How can I obtain D-Lead® test kits?

    The D-Lead® test kits are available for purchase from certain distributors and retail outlets. Locate a distributor or retailer online , email [email protected] or call 414-962-3006. Question Number: 23002-16390 Find a printable PDF copy of all frequent questions pertaining to lead .

    • Last published:

  • Is lead paint testing required under the Lead Renovation, Repair and Painting (RRP) Rule?

    No. A firm can either assume lead-based paint is present and follow the requirements of the RRP Rule (which requires no testing), or test and if lead-based paint is found follow the requirements of the regulation. Question Number: 23002-32338 Find a printable PDF copy of all frequent questions pertaining to…

    • Last published:

  • Will boiling my water help?

    No. Boiling water will NOT reduce nitrate levels. In fact, it will make the level of nitrate worse because some of the water will evaporate but the nitrate will not. This increases the concentration of nitrate in water.

    • Last published:

  • Is it safe to shower or bathe in water if it is over the nitrate MCL of 10 mg/L?

    Nitrate is only a concern for ingestion (eating and drinking). It is not absorbed through your skin. People who install filter systems for nitrate often install them just for their kitchen sink faucet, and they use that faucet for their cooking and drinking water.

    • Last published:

  • What should I do if my water has elevated nitrates and/or exceeds the MCL?

    If nitrate exceeds the MCL of 10 mg/L, you should find a safe alternative drinking water supply. The quickest thing to do is to begin using bottled water for drinking. Another option is to install a treatment that will remove nitrate from your water such as reverse osmosis or a…

    • Last published:

  • Why is nitrate contamination a concern?

    Nitrate is an acute contaminant, meaning that health effects can occur immediately (I.e. within hours or days) of short-term exposure. Too much nitrate in your body makes it harder for red blood cells to carry oxygen. While most people recover quickly, this can be very dangerous for infants and some…

    • Last published:

  • What lead test kits are recognized by EPA?

    Answer: EPA recognizes three lead test kits for use in complying with the negative response criterion of the RRP rule. They are the Luxfer Magtech LeadCheck TM kit (for use on ferrous metal, plaster, drywall and wood), the State of Massachusetts kit (for use on drywall, plaster), and the D-Lead®…

    • Last published:

  • Does EPA recognize the Luxfer Magtech LeadCheckTM test kit for use on red paint?

    Yes. EPA recognizes this lead test kit for use on any color paint as long as the lead test kit is used in accordance with the manufacturer’s instructions. Note: 3M has sold the formulation and trademarks related to the 3M™ LeadCheck™ test kits to Luxfer Magtech. EPA recognizes the LeadCheck™…

    • Last published:

  • How does the Fuel Wizard Determine which Fuel Formulations to Modify?

    See More Frequent Questions about MOVES and Related Models . The Fuel Wizard only works on fuel formulations that are in your county database (CDB) and it "edits" them to comply with the alterations you provide. If you wish to create a set of alternate fuels, you will need to…

    • Last published:

  • Where Does EPA Obtain Default Vehicle Miles Traveled (VMT)?

    See More Frequent Questions about MOVES and Related Models . MOVES gets default national vehicle miles traveled (VMT) values from the Highway Performance Monitoring System (HPMS) of the Federal Highway Administration, which collects VMT information from every state. Although this is a good source of consistent total VMT information, the…

    • Last published:

  • How Do I Create my Own I/M Program Input Table Using the "Create Template" Option?

    See More Frequent Questions about MOVES and Related Models . If you already have an I/M program in your area, you should always begin by exporting the default I/M program in MOVES, reviewing it, making any changes to the default program, and re-importing it, rather than trying to fill a…

    • Last published: