Search Frequent Questions

Filter By:

Active filters:

Remove all filters

Displaying 1 - 15 of 24 results

  • How do I Obtain the Populations for Each of the MOVES Source Types?

    See More Frequent Questions about MOVES and Related Models . To output vehicle populations, when setting up your RunSpec select the "Inventory" calculation type from the Scale panel and the "Population" activity option from the General Output panel of the MOVES GUI. The movesactivityoutput table in your MOVES output database…

    • Last published:

  • How are Counties Mapped to Fuel Regions in MOVES? How Can I Substitute Alternate Fuel Formulations?

    See More Frequent Questions about MOVES and Related Models . The RegionCounty table in the MOVES default database maps each county to a MOVES fuel region (defined by regionCodeID). If you are conducting a County or Project Scale Run, you do not need to modify this table to use alternate…

    • Last published:

  • Can MOVES Report Output in Terms of Fuel Consumption?

    See More Frequent Questions about MOVES and Related Models . Although gallons of fuel consumed are not reported by MOVES, the factors used to convert total energy consumption (a MOVES reporting option) to gallons of fuel are contained in the FuelSubtype table (energy content, reported in kilojoules per gram of…

    • Last published:

  • How do I use MOVES at Project Scale?

    See More Frequent Questions about MOVES and Related Models . The MOVES model can estimate emissions at national, county or project scale. Project scale is useful for estimating an individual transportation project like an intersection or transit project, but it requires detailed inputs that describing the vehicle population and activity…

    • Last published:

  • How Can I Determine the Effect of Speed on Vehicle Emissions?

    See More Frequent Questions about MOVES and Related Models . MOVES can be run in either “Inventory” or “Emission Rates” mode. With Emission Rates, MOVES reports emission rates for the 16 average speed bins used by MOVES for each hour of the day and additional emission rate output that may…

    • Last published:

  • Does MOVES Incorporate Anticipated Improvements in VOC Emission Factors Resulting from Improved Fuel Economy?

    See More Frequent Questions about MOVES and Related Models . Changes in fuel consumption affect VOC emissions by reducing refueling vapor losses and spillage. Other emissions (such as sulfates) are also affected by fuel consumption. MOVES incorporates changes due to fuel economy requirements that were finalized as of the date…

    • Last published:

  • Can I use MOVES to Model Emissions from Vehicles in other Countries?

    See More Frequent Questions about MOVES and Related Models . The MOVES model was designed specifically to model the emissions from vehicles and equipment designed to meet emission standards in the United States. There are considerable challenges to adapting the MOVES framework to other nations, primarily around the need for…

    • Last published:

  • How can I run MOVES3 for the entire U.S or for an entire year?

    See More Frequent Questions about MOVES and Related Models . The most accurate national MOVES runs are done for every county and hour and then averaged together in the output, but, depending on your intended use of the results, it’s also possible to pre-aggregate the MOVES inputs to run the…

    • Last published:

  • How does the Fuel Wizard Determine which Fuel Formulations to Modify?

    See More Frequent Questions about MOVES and Related Models . The Fuel Wizard only works on fuel formulations that are in your county database (CDB) and it "edits" them to comply with the alterations you provide. If you wish to create a set of alternate fuels, you will need to…

    • Last published:

  • Where Does EPA Obtain Default Vehicle Miles Traveled (VMT)?

    See More Frequent Questions about MOVES and Related Models . MOVES gets default national vehicle miles traveled (VMT) values from the Highway Performance Monitoring System (HPMS) of the Federal Highway Administration, which collects VMT information from every state. Although this is a good source of consistent total VMT information, the…

    • Last published:

  • How Do I Create my Own I/M Program Input Table Using the "Create Template" Option?

    See More Frequent Questions about MOVES and Related Models . If you already have an I/M program in your area, you should always begin by exporting the default I/M program in MOVES, reviewing it, making any changes to the default program, and re-importing it, rather than trying to fill a…

    • Last published:

  • Where Can I Find Default HPMSBaseYearVMT Values for a Specific County?

    See More Frequent Questions about MOVES and Related Models . MOVES does calculate default values for VMT for each calendar year for each county. Since these values are calculated, they are not found in any table in the default database. If you wish to obtain the default estimates, you will…

    • Last published:

  • Why Does the "hourvmtfraction" Table in the MOVES Default Database Include Fractions for roadTypeID 1 (off-network)?

    See More Frequent Questions about MOVES and Related Models . The original concept for MOVES assumed that there would be some vehicle miles traveled (VMT) not accounted for in the other four road types. This remaining VMT would be accounted for in roadTypeID=1. As the model developed, it was decided…

    • Last published:

  • Can Programs Other Than Microsoft Excel be Used to Edit Input Database Files?

    See More Frequent Questions about MOVES and Related Models . Yes. In addition to MS Excel files, in the County Data Manager/Project Data Manager, MOVES can read in other file types using ASCII text and comma separated variables.

    • Last published:

  • What are the features available on the MOVES “Advanced Features” panel, and when would I use them?

    The MOVES graphical user interface (GUI) includes a panel for “Advanced Features,” which allows modelers to edit RunSpec inputs for preaggregation options and select input databases created by MOVES tools. The panel also includes some options that are obsolete or intended only for MOVES testing and development work. Each of…

    • Last published: